Heavy Duty Steel Structure

Storage tanks are containers that hold liquids, compressed gases (gas tank; or in U.S.A "pressure vessel", which is not typically labeled or regulated as a storage tank) or mediums used for the short- or long-term storage of heat or cold. The term can be used for reservoirs, and for manufactured containers. High pressure storage tank and large storage tank are common equipment for storing liquids or gases. Their main difference lies in their design and use. High pressure storage tank are...

The operation process of stable continuous evaporative crystallizer can be divided into countercurrent method, downstream method, cross flow method, and flat flow method. In addition to these four processes, other processes can also be arranged according to production conditions. For example, sometimes, in most evaporation processes, after introducing secondary steam and using it as heating steam, not every effect occurs. On the contrary, a portion of the secondary steam is used to preheat the...

The industrial material reactor is composed of kettle body, kettle cover, jacket, agitator, transmission device, shaft seal device, support and so on. The mixing form is generally anchor type, slurry type, turbine type, propulsion type or frame type, etc. When the height of the stirring device is relatively large, multi-layer stirring blade can be used, or any selection can be made according to the requirements of the user. And a jacket is arranged outside the kettle wall, or a heat replacement...

The hydrogenation reaction kettle can be divided into two categories: One is the traditional stirred reactor. Gas in the upper space of the vessel can not be circulated in the liquid phase, because of the miscibility and density difference of the gas and liquid. The unreacted gas accumulates in the upper space of the reactor in the reactor, which seriously affects the reaction rate.The other is the reaction kettle in which the gas is circulated in the liquid phase. Gas-liquid reaction is a kind...

High-Performance Material Reactor consists of a set of special components to achieve transmission requirements and shear deformation, high gas internal circulation and turbulence.When motor rotates by driving internal hollow agitator the centrifugal force produced by the circular motion of the fluid nearby under the action of the impeller makes the agitator self-priming, when negative pressure zone is formed, inner part will connected to gas through air axis,Thus, the gas on liquid surface is...

Reactor Introduction: 1. Types: tubular reactor, tank reactor, solid particle bed reactor, tower reactor, jet reactor and other atypical reactor. 2. Concrete products: reactor, reaction kettle, autoclave, high-pressure kettle, high-pressure autoclave, super autoclave, synthetic tower, decomposition pan, vulcanizer, decomposition tower, polymerization kettle, transform furnace, cooking pot, steamed ball, gas furnace. 3. Materials: carbon steel, low-alloy steel, stainless steel and non-ferrous...

U-tube heat exchanger Product Advantages ● Experienced sales and professional after-sales group can provide 24hours consulting service. ● Long-term relationship with one more than experienced factory for providing high-level man ufacturing standard. ● High quality supplier for assuring the good performance of motors, fans,condenser heat exchanger, EX-pumps ,valves and ect. ● Competitive Price , Flexible Modular Design, Experience on running projects. From Engineering design, High-quality...

Spiral board plate heat exchanger is a kind of high efficiency heat exchanger equipment, which is suitable for vapor to vapor, vapor to liquid, liquid to liquid and liquid to liquid heat transfer. It is suitable for chemical, petroleum, solvent, medicine, food, light industry, textile, metallurgy, steel rolling, coking and other industries. According to the structure, it can be divided into non detachable (type I) spiral plate heat exchanger and detachable (type II, type III) spiral plate heat...

Main Features: 1) Material: stainless steel and/or carbon steel 2) Heat exchanger area: 1 - 250sqm 3) Type: non-detachable or detachable ,horizontal or vertical type 4)Used for steam to steam, liquid to liquid, and steam to liquid heat transferring and exchanging The spiral heat exchanger (SHE) is a high-efficiency heat exchanger used for heat exchanging in factories of ethanol(alcohol),chemical, petroleum, pharmacy, food, light-industry, textile, metallurgy, steel rolling and coking industry...

Large Storage Tank are containers that hold liquids, compressed gases (gas tank; or in U.S.A "pressure vessel", which is not typically labeled or regulated as a storage tank) or mediums used for the short- or long-term storage of heat or cold. The term can be used for reservoirs, and for manufactured containers. A high pressure storage tank is a container used to store high-pressure gases or liquids. It is usually made of steel and can withstand high pressures to ensure that the stored gas or...

Product Intriduction: ■Easy operation With an amount of concentration cycles set using the one-touch counter, concentration of the solution is automatically repeated until the correct value is obtained. Maintenance is very easy due to the simple structure. ■Wide variety of sizes The volume of evaporation is standardized from 50L/H to 2,000L/H. The natural circulation external heating evaporator consists of a tube heater, an evaporating chamber and a circulating tube. If crystallization occurs...

Natural circulation evaporator heat exchange loop evaporation separation process does not require external power can be naturally formed, the natural circulation evaporative heat exchange unit may be composed of a vertical tube, horizontal tube, snake tube, shaped tubes, plates and other components, solution was evaporated by heating the material after heat exchange can be isolated in the surface of the heat exchange unit is completed and to be completed in the outer surface of the heat...

Extraction tower configuration and Characteristics 1. The tower, the intermediate section of the extraction tower, is an upright cylinder. It can also be made of stainless steel or high borosilicate glass according to the size of the extraction. 2. the internal components and pipes of the extraction tower are made of stainless steel. 3. the extraction device is easy to clean and suitable for organic mixtures with high viscosity. Stainless steel extraction tower introduction: Extraction tower...

Chemical raw storage tank can be divided into the following categories based on their purpose and characteristics: 1. Storage tank: mainly used for storing liquid chemical raw materials, such as petroleum, chemicals, alcohol, ammonia, etc. Storage tanks are generally made of materials such as steel, fiberglass, and concrete, which have the characteristics of anti-corrosion, explosion-proof, and leak proof. 2. Mixing tank: mainly used for chemical raw materials in mixing, stirring, reaction and...

Our services We can provide you with high quality products. Quality service. And accept customer according to your request. If you have any questions. please tell me. I will fix it for you as soon as possible.Warm-hearting service to help you find suitable stainless steel storage tank. Lined Anticorrosive Storage Tank Advantages : All these tanks are extremely rugged in state and offer high level of performance with accuracy. Product process 1). cutting materials for preparing oil tanks...

Lined Anticorrosive Storage Tank Product process 1). cutting materials for preparing oil tanks manufacture 2). rolling machines for circling 3). welding and NDT(non-defection test) inspection 4). re-circling after welding 5). outer vessel’s abrasive blasting and anti corrosive painting for outside surface 6). pipe connecting and assembly of inner vessel and outer vessel 7). valves installation 8). perlite filling 9). vacuum-pumping 10). final painting and ready for shipment Our services We can...

Finned tubes are the main components of heat exchangers. They are a series of tubes where fins have been added on the outside to increase the contact area with the outside fluid, to exchange heat and between the fluid inside the tube and the fluid outside the tube. Finned tube heat exchanger are known for maximizing heat transfer surface area, by design. Finned tube heat exchangers have tubes with extended outer surface area or fins to enhance the heat transfer rate from the additional area of...

Float valve tray and metal sieve tray are commonly used fillers in chemical equipment, and their main function is to increase the surface area of chemical reactors or separation towers to improve reaction or separation efficiency. 1. Adjustable float valve tray: It can be used in tower equipment in industries such as chemical, petroleum, and pharmaceutical industries. Its main function is to control the liquid level and airflow speed inside the tower and improve separation efficiency. 2....

Corrugated plate structural filler, high efficiency corrugated filler, high flow corrugated filler, and high temperature corrugated filler are commonly used types of fillers in chemical equipment. Corrugated plate structure filler is a type of packing composed of corrugated plates, which has high mass transfer efficiency and separation effect, and is suitable for packing towers and adsorption towers of various chemical equipment. High efficiency corrugated filler is a type of packing composed...

Corrugated plate structure filler is a type of packing composed of corrugated plates, which has high mass transfer efficiency and separation effect, and is suitable for packing towers and adsorption towers of various chemical equipment. High efficiency corrugated filler is a type of packing composed of multiple corrugated sheets, with high surface area and mass transfer efficiency, suitable for packing and adsorption towers of various chemical equipment. High flow corrugated filler is a type of...