Steel Structure Equipment Framework

Storage tanks are containers that hold liquids, compressed gases (gas tank; or in U.S.A "pressure vessel", which is not typically labeled or regulated as a storage tank) or mediums used for the short- or long-term storage of heat or cold. The term can be used for reservoirs, and for manufactured containers. High pressure storage tank and large storage tank are common equipment for storing liquids or gases. Their main difference lies in their design and use. High pressure storage tank are...

The operation process of stable continuous evaporative crystallizer can be divided into countercurrent method, downstream method, cross flow method, and flat flow method. In addition to these four processes, other processes can also be arranged according to production conditions. For example, sometimes, in most evaporation processes, after introducing secondary steam and using it as heating steam, not every effect occurs. On the contrary, a portion of the secondary steam is used to preheat the...

The industrial material reactor is composed of kettle body, kettle cover, jacket, agitator, transmission device, shaft seal device, support and so on. The mixing form is generally anchor type, slurry type, turbine type, propulsion type or frame type, etc. When the height of the stirring device is relatively large, multi-layer stirring blade can be used, or any selection can be made according to the requirements of the user. And a jacket is arranged outside the kettle wall, or a heat replacement...

The hydrogenation reaction kettle can be divided into two categories: One is the traditional stirred reactor. Gas in the upper space of the vessel can not be circulated in the liquid phase, because of the miscibility and density difference of the gas and liquid. The unreacted gas accumulates in the upper space of the reactor in the reactor, which seriously affects the reaction rate.The other is the reaction kettle in which the gas is circulated in the liquid phase. Gas-liquid reaction is a kind...

High-Performance Material Reactor consists of a set of special components to achieve transmission requirements and shear deformation, high gas internal circulation and turbulence.When motor rotates by driving internal hollow agitator the centrifugal force produced by the circular motion of the fluid nearby under the action of the impeller makes the agitator self-priming, when negative pressure zone is formed, inner part will connected to gas through air axis,Thus, the gas on liquid surface is...

Reactor Introduction: 1. Types: tubular reactor, tank reactor, solid particle bed reactor, tower reactor, jet reactor and other atypical reactor. 2. Concrete products: reactor, reaction kettle, autoclave, high-pressure kettle, high-pressure autoclave, super autoclave, synthetic tower, decomposition pan, vulcanizer, decomposition tower, polymerization kettle, transform furnace, cooking pot, steamed ball, gas furnace. 3. Materials: carbon steel, low-alloy steel, stainless steel and non-ferrous...

U-tube heat exchanger Product Advantages ● Experienced sales and professional after-sales group can provide 24hours consulting service. ● Long-term relationship with one more than experienced factory for providing high-level man ufacturing standard. ● High quality supplier for assuring the good performance of motors, fans,condenser heat exchanger, EX-pumps ,valves and ect. ● Competitive Price , Flexible Modular Design, Experience on running projects. From Engineering design, High-quality...

Spiral board plate heat exchanger is a kind of high efficiency heat exchanger equipment, which is suitable for vapor to vapor, vapor to liquid, liquid to liquid and liquid to liquid heat transfer. It is suitable for chemical, petroleum, solvent, medicine, food, light industry, textile, metallurgy, steel rolling, coking and other industries. According to the structure, it can be divided into non detachable (type I) spiral plate heat exchanger and detachable (type II, type III) spiral plate heat...

Spiral plate heat exchanger Nominal pressure PG is 0.6, 1.0, 1.6MPa. The allowable working temperature of carbon steel spiral plate heat exchanger is -20°C~250°C; Stainless steel is -20°C~320°C. When the equipment is selected, the fluid in the equipment channel should reach the turbulent state (general liquid flow rate) of 1m/ SEC through the appropriate process calculation; Gas velocity > 10 m/SEC. Equipment has vertical, horizontal, hanging three types of installation. For steam...

Spirotal heat exchanger equipment Usage & Applications: A stainless steel spiral heat exchanger is a high-efficiency heat exchanger suitable for steam-steam, steam-liquid and liquid-liquid heat transfer. It adapts for chemical, petroleum, pharmacy, food, light-industry, textile, metallurgy, steel rolling and coking industry etc. According to the structure, it can be divided into un-detachable (Model I) and detachable (Model III) . Spiral board plate heat exchanger Nominal pressure PG is...

Spiral plate heat exchanger Nominal pressure PG is 0.6, 1.0, 1.6MPa. The allowable working temperature of carbon steel is -20°C~250°C; Stainless steel is -20°C~320°C. When the equipment is selected, the fluid in the equipment channel should reach the turbulent state (general liquid flow rate) of 1m/ SEC through the appropriate process calculation; Gas velocity > 10 m/SEC. Equipment has vertical, horizontal, hanging three types of installation. For steam condensation can only be cubic....

Main Features: 1) Material: stainless steel and/or carbon steel 2) Heat exchanger area: 1 - 250sqm 3) Type: non-detachable or detachable ,horizontal or vertical type 4)Used for steam to steam, liquid to liquid, and steam to liquid heat transferring and exchanging The spiral heat exchanger (SHE) is a high-efficiency heat exchanger used for heat exchanging in factories of ethanol(alcohol),chemical, petroleum, pharmacy, food, light-industry, textile, metallurgy, steel rolling and coking industry...

Large Storage Tank are containers that hold liquids, compressed gases (gas tank; or in U.S.A "pressure vessel", which is not typically labeled or regulated as a storage tank) or mediums used for the short- or long-term storage of heat or cold. The term can be used for reservoirs, and for manufactured containers. A high pressure storage tank is a container used to store high-pressure gases or liquids. It is usually made of steel and can withstand high pressures to ensure that the stored gas or...

Its structure is roughly the same as film-lift evaporator, liquid is added from top. A liquid distribution device is installed at the top of each tube, so that the liquid can be uniformly received.The secondary steam and the concentrated liquid generally flow together, and the material liquid flows along the pipe wall in a film form due to the action of the secondary steam. The liquid film flow uses gravity instead of overcoming gravity and thus vaporizes the solution with greater viscosity....

Product Intriduction: ■Easy operation With an amount of concentration cycles set using the one-touch counter, concentration of the solution is automatically repeated until the correct value is obtained. Maintenance is very easy due to the simple structure. ■Wide variety of sizes The volume of evaporation is standardized from 50L/H to 2,000L/H. The natural circulation external heating evaporator consists of a tube heater, an evaporating chamber and a circulating tube. If crystallization occurs...

Natural circulation evaporator heat exchange loop evaporation separation process does not require external power can be naturally formed, the natural circulation evaporative heat exchange unit may be composed of a vertical tube, horizontal tube, snake tube, shaped tubes, plates and other components, solution was evaporated by heating the material after heat exchange can be isolated in the surface of the heat exchange unit is completed and to be completed in the outer surface of the heat...

Introduction of Industrial extraction tower equipment: Extraction tower machine is a kind of tower extraction equipment of mechanical stirring, it is composed by upper settling chamber, emulsion chamber and bottom settling chamber. the emulsion chamber is cylinder type, and is divided into several extraction chambers by static ring baffle, there is a fixed turnplate between two static ring baffles, and rotating with shaft together. When work, heavy phase(aqueous)and light phase(organic phase)...

Extraction tower configuration and Characteristics 1. The tower, the intermediate section of the extraction tower, is an upright cylinder. It can also be made of stainless steel or high borosilicate glass according to the size of the extraction. 2. the internal components and pipes of the extraction tower are made of stainless steel. 3. the extraction device is easy to clean and suitable for organic mixtures with high viscosity. Stainless steel extraction tower introduction: Extraction tower...

Industrial distillation tower are large-scale chemical equipment mainly used for large-scale separation and purification processes in industrial production. It is usually composed of multiple distillation columns, capable of handling a large amount of mixture, and capable of continuous operation to improve production efficiency. Industrial distillation towers are widely used in industries such as petrochemical, pharmaceutical, food, and chemical fiber, and are one of the indispensable equipment...

Industrial washing tower is a device used to remove pollutants from the air, usually used in industrial waste gas treatment. It is a kind of vertically mounted tower equipment, filled with adsorption materials, such as activated carbon, molecular sieve, waste gas through the tower body packing layer, and adsorption material contact, so as to remove pollutants. 1.The efficiency of dust removal and desulfurization is high and the efficiency of desulfurization can reach 85% when using alkaline...